Practical Mechanical Drawing and Machine Design, Self Taught ...Frederick J. Drake & Company, 1906 - 157 sider |
Inni boken
Resultat 1-5 av 47
Side 13
... inches , not counting the small portion at each end , which is undivided , and whose use is to protect the end graduations from injury . A scale should be used for dimensioning drawings only , and not used as a ruler or straight - edge ...
... inches , not counting the small portion at each end , which is undivided , and whose use is to protect the end graduations from injury . A scale should be used for dimensioning drawings only , and not used as a ruler or straight - edge ...
Side 15
... inch of the lead . The end of the lead should then be sharpened to a chisel or wedge - shaped point on the sand paper block . Fig . 20 - Sand Paper Pencil Sharpener . Pencil Erasers . A pencil eraser or rubber should be of soft , fine ...
... inch of the lead . The end of the lead should then be sharpened to a chisel or wedge - shaped point on the sand paper block . Fig . 20 - Sand Paper Pencil Sharpener . Pencil Erasers . A pencil eraser or rubber should be of soft , fine ...
Side 16
... inches in size . The material should be of first quality clear soft pine , free from pitch and thoroughly kiln dried . The board should be made of five or six strips about 4 by 27 inches , well glued together and held from warping by ...
... inches in size . The material should be of first quality clear soft pine , free from pitch and thoroughly kiln dried . The board should be made of five or six strips about 4 by 27 inches , well glued together and held from warping by ...
Side 18
... inch , operated by the milled thumb - nut shown . Water Colors . These may be obtained in the form of a thick paste in small porcelain pans , or Fig . 31 - Beam Compass with Pen , Pencil and Needle - Points . with much difficulty . For ...
... inch , operated by the milled thumb - nut shown . Water Colors . These may be obtained in the form of a thick paste in small porcelain pans , or Fig . 31 - Beam Compass with Pen , Pencil and Needle - Points . with much difficulty . For ...
Side 51
... F - Force required at end of lever . N - Number of threads per inch of jack screw . P = 6.283 ( NXRXF ) F P 6.283 ( NXR ) N = P 6.283 ( RXF ) R = Р 6.283 ( NXF ) The Spiral is a curve generated by a point mov- THE MECHANICAL POWERS 51.
... F - Force required at end of lever . N - Number of threads per inch of jack screw . P = 6.283 ( NXRXF ) F P 6.283 ( NXR ) N = P 6.283 ( RXF ) R = Р 6.283 ( NXF ) The Spiral is a curve generated by a point mov- THE MECHANICAL POWERS 51.
Andre utgaver - Vis alle
Practical Mechanical Drawing and Machine Design Self Taught: Drafting Tools ... Charles Westinghouse Ingen forhåndsvisning tilgjengelig - 2016 |
Practical Mechanical Drawing and Machine Design Self Taught: Drafting Tools ... Charles Westinghouse Ingen forhåndsvisning tilgjengelig - 2018 |
Vanlige uttrykk og setninger
angle iron beam compass bisect blade boiler bolts cast cast-iron circular pitch clearance common logarithm condenser coupling coupling rod crank cubic contents curve cylinder describe arcs Diam diametral pitch dimensions distance divide draw the line edge ellipse engine eter Example F-Force figure find the area flange gear given gusset hammer horsepower inclined plane intersecting joint length lever machine mantissa mechanism Multiply the power number of equal number of teeth P₁ paper pencil perpendicular phosphor bronze pipe piston pitch circle pitch diameter plates pound weight pounds per square pressure pulley radius revolutions per minute right angles rivets screw semicircle shaft shown in Fig side space square inch steel straight line stroke stuffing-box superficial area surface Surface Condensers T-square thickness tiply tooth traced triangle tubes valves velocity vertical wedge weight of steam wheel width wrought iron
Populære avsnitt
Side 21 - When a straight line standing on another straight line makes the adjacent angles equal to one another, each of the angles is called a right angle ; and the straight line which stands on the other is called a perpendicular to it.
Side 30 - С into as many equal parts as the polygon is to have sides.
Side 43 - To find the. area of a triangle when the three sides are given. From half the sum of the three sides...
Side 22 - A circle is a plane figure contained by one line, which is called the circumference, and is such, that all straight lines drawn from a certain point within the figure to the circumference are equal to one another : 16. And this point is called the centre of the circle.
Side 41 - To the sum of the areas of the two ends of the frustum, add the square root of the product of the diameters of the two ends, this result multiplied by one-third of the perpendicular height of the frustum will give the cubic contents.
Side 43 - From half the sum of the three sides subtract each side severally. Multiply the half sum and the three remainders...
Side 26 - A cone is a solid figure described by the revolution of a right-angled triangle about one of the sides containing the right angle, which side remains fixed.
Side 21 - A plane angle is the inclination of two lines to one another in a plane, which meet together, but are not in the same direction.
Side 117 - Let the given velocity of a wheel containing 54 teeth equal 16 revolutions per minute, and the given diameter of an intermediate pulley equal 25 inches, to obtain a velocity of 81 revolutions in a machine ; required the number of teeth in the intermediate wheel, and diameter of the last pulley. v/81...
Side 153 - The logarithm of a number is the exponent of the power to which it is necessary to raise a fixed number, in order to produce the first number.