Practical Mechanical Drawing and Machine Design, Self Taught ...Frederick J. Drake & Company, 1906 - 157 sider |
Inni boken
Resultat 1-5 av 13
Side 34
... two divisions on the lines 4 and 8 , three divisions on the lines 3 and 9 , four divisions on the lines 2 and 10 , and five divisions on the lines 1 and 11. A line traced through the points thus 34 MECHANICAL DRAWING.
... two divisions on the lines 4 and 8 , three divisions on the lines 3 and 9 , four divisions on the lines 2 and 10 , and five divisions on the lines 1 and 11. A line traced through the points thus 34 MECHANICAL DRAWING.
Side 35
Charles Westinghouse. E Fig . 83 , MENSURATION. 1 and 11. A line traced through the points thus obtained will be the cycloid curve required . To develop a spiral with uniform spacing - Fig . 83. Divide the line BE into as many equal parts ...
Charles Westinghouse. E Fig . 83 , MENSURATION. 1 and 11. A line traced through the points thus obtained will be the cycloid curve required . To develop a spiral with uniform spacing - Fig . 83. Divide the line BE into as many equal parts ...
Side 69
... tracing cloth is placed above the orig- inal and the lines of the drawing traced on the new surface , as though one were inking a pencilled drawing . Tracing cloth is usually furnished with one surface glazed and the other dull . Either ...
... tracing cloth is placed above the orig- inal and the lines of the drawing traced on the new surface , as though one were inking a pencilled drawing . Tracing cloth is usually furnished with one surface glazed and the other dull . Either ...
Side 75
... tracing cloth with several lines on its surface and lay these small pieces out at the same time the real print is ... tracing , in order to leave an edge around it when the tracing is placed upon it . From ten to twelve sheets are placed ...
... tracing cloth with several lines on its surface and lay these small pieces out at the same time the real print is ... tracing , in order to leave an edge around it when the tracing is placed upon it . From ten to twelve sheets are placed ...
Side 85
... traced on the side of a toothed wheel , and is rather nearer the points of the teeth than the roots . Pitch of Teeth . The distance from the center of one tooth to the center of the next , or from the front of one to the front of the ...
... traced on the side of a toothed wheel , and is rather nearer the points of the teeth than the roots . Pitch of Teeth . The distance from the center of one tooth to the center of the next , or from the front of one to the front of the ...
Andre utgaver - Vis alle
Practical Mechanical Drawing and Machine Design Self Taught: Drafting Tools ... Charles Westinghouse Ingen forhåndsvisning tilgjengelig - 2016 |
Practical Mechanical Drawing and Machine Design Self Taught: Drafting Tools ... Charles Westinghouse Ingen forhåndsvisning tilgjengelig - 2018 |
Vanlige uttrykk og setninger
angle iron beam compass bisect blade boiler bolts cast cast-iron circular pitch clearance common logarithm condenser coupling coupling rod crank cubic contents curve cylinder describe arcs Diam diametral pitch dimensions distance divide draw the line edge ellipse engine eter Example F-Force figure find the area flange gear given gusset hammer horsepower inclined plane intersecting joint length lever machine mantissa mechanism Multiply the power number of equal number of teeth P₁ paper pencil perpendicular phosphor bronze pipe piston pitch circle pitch diameter plates pound weight pounds per square pressure pulley radius revolutions per minute right angles rivets screw semicircle shaft shown in Fig side space square inch steel straight line stroke stuffing-box superficial area surface Surface Condensers T-square thickness tiply tooth traced triangle tubes valves velocity vertical wedge weight of steam wheel width wrought iron
Populære avsnitt
Side 21 - When a straight line standing on another straight line makes the adjacent angles equal to one another, each of the angles is called a right angle ; and the straight line which stands on the other is called a perpendicular to it.
Side 30 - С into as many equal parts as the polygon is to have sides.
Side 43 - To find the. area of a triangle when the three sides are given. From half the sum of the three sides...
Side 22 - A circle is a plane figure contained by one line, which is called the circumference, and is such, that all straight lines drawn from a certain point within the figure to the circumference are equal to one another : 16. And this point is called the centre of the circle.
Side 41 - To the sum of the areas of the two ends of the frustum, add the square root of the product of the diameters of the two ends, this result multiplied by one-third of the perpendicular height of the frustum will give the cubic contents.
Side 43 - From half the sum of the three sides subtract each side severally. Multiply the half sum and the three remainders...
Side 26 - A cone is a solid figure described by the revolution of a right-angled triangle about one of the sides containing the right angle, which side remains fixed.
Side 21 - A plane angle is the inclination of two lines to one another in a plane, which meet together, but are not in the same direction.
Side 117 - Let the given velocity of a wheel containing 54 teeth equal 16 revolutions per minute, and the given diameter of an intermediate pulley equal 25 inches, to obtain a velocity of 81 revolutions in a machine ; required the number of teeth in the intermediate wheel, and diameter of the last pulley. v/81...
Side 153 - The logarithm of a number is the exponent of the power to which it is necessary to raise a fixed number, in order to produce the first number.