Modern Sheet-metal Workers' Instructor: Practical Geometry, Mensuration, Properties of Metals and Alloys ...Drake, 1906 - 309 sider |
Inni boken
Resultat 6-10 av 19
Side 163
... curves g , h , 1 , k from the center m , Fig . 154. Transfer the ec , Fig . 153 , from g to r and from g to n , Fig . 154 , also from n to o and r to b , and draw lines from r , b , n , and o to the center m . Connecting the points br ...
... curves g , h , 1 , k from the center m , Fig . 154. Transfer the ec , Fig . 153 , from g to r and from g to n , Fig . 154 , also from n to o and r to b , and draw lines from r , b , n , and o to the center m . Connecting the points br ...
Side 166
... Fig . 160. Take the length from B to j ' and set it off from j to j ' in Fig . 160 . Take the length B to i " and set it off from i to i ' , and so L B on . A curve drawn through the points c '. 164 PRACTICAL PROBLEMS.
... Fig . 160. Take the length from B to j ' and set it off from j to j ' in Fig . 160 . Take the length B to i " and set it off from i to i ' , and so L B on . A curve drawn through the points c '. 164 PRACTICAL PROBLEMS.
Side 167
... curve through all the points of intersection , as n , m , 1 , k , i , h , and g . This will form the curve for half of the pattern . To describe the patterns for two pipes which inter- sect at an angle . Let DAEC represent the larger ...
... curve through all the points of intersection , as n , m , 1 , k , i , h , and g . This will form the curve for half of the pattern . To describe the patterns for two pipes which inter- sect at an angle . Let DAEC represent the larger ...
Side 169
... curve from a to M. Divide the curve from L to M into three equal parts , and then draw perpendicular lines from these points to intersect the semicircle ABC , as df , eg , Mh . Draw lines parallel to AD from f to i , g to k , and h to 1 ...
... curve from a to M. Divide the curve from L to M into three equal parts , and then draw perpendicular lines from these points to intersect the semicircle ABC , as df , eg , Mh . Draw lines parallel to AD from f to i , g to k , and h to 1 ...
Side 170
... curve drawn these Fig . 166 . D A EF Fig . 167 . points will give the shape of the opening in the larger pipe . To make a set of patterns for an oval tea - kettle . When getting out the patterns for an oval tea - kettle to hold 6 quarts ...
... curve drawn these Fig . 166 . D A EF Fig . 167 . points will give the shape of the opening in the larger pipe . To make a set of patterns for an oval tea - kettle . When getting out the patterns for an oval tea - kettle to hold 6 quarts ...
Andre utgaver - Vis alle
Modern Sheet-Metal Workers' Instructor: Practical Geometry, Mensuration ... Joseph H Rose Ingen forhåndsvisning tilgjengelig - 2018 |
Modern Sheet-Metal Workers' Instructor: Practical Geometry, Mensuration ... Joseph H. Rose Ingen forhåndsvisning tilgjengelig - 2022 |
Modern Sheet-Metal Workers' Instructor: Practical Geometry, Mensuration ... Joseph H Rose Ingen forhåndsvisning tilgjengelig - 2018 |
Vanlige uttrykk og setninger
66 IXXX alloys aluminium ammoniac annealed antimony bending bismuth body boiling borax bottom brass brazing cast iron chloride of zinc circle circumference clean coated copper copper bit cubic contents curve cutter cylinder degrees Fahrenheit describe dipped dissolve draw the line ductility edge ENGINEERING feet fire flux foot gallons galvanized gills glue hammer hardened heat hole inches in diameter IXXXX joint lead leather length machine shown malleable melted molten Multiply muriatic acid nitric acid number of equal oxide pattern perpendicular piece pints pipe plates points pounds pressure radius right angles rolls rosin round salammoniac screw shape shears sheet metal shown in Fig sides solder solution speculum metal spelter square inch stake steel straight line substances sulphuric sulphuric acid superficial area surface temperature thick tion triangle tube velocity vessel Weight width Wire Gauge WROUGHT IRON zinc zine
Populære avsnitt
Side 5 - When a straight line standing on another straight line makes the adjacent angles equal to one another, each of the angles is called a right angle ; and the straight line which stands on the other is called a perpendicular to it.
Side 21 - AB of the circle into as many equal parts as the polygon is to have sides. With the points A and B as centers and radius AB, describe arcs cutting each other at C.
Side 224 - To find the pressure in pounds per square inch of a column of water, multiply the height of the column in feet by .434. Approximately, we say that every foot elevation is equal to % Ib. pressure per square inch ; this allows for ordinary friction. To find the diameter of a pump cylinder...
Side 227 - To find the velocity in feet per minute necessary to discharge a given volume of water in a given time, multiply the number of cubic feet of water by 144 and divide the product by the area of the pipe in inches.
Side 43 - To find the. area of a triangle when the three sides are given. From half the sum of the three sides...
Side 10 - A circle is a plane figure contained by one line, which is called the circumference, and is such, that all straight lines drawn from a certain point within the figure to the circumference are equal to one another : 16. And this point is called the centre of the circle.
Side 5 - A plane angle is the inclination of two lines to one another in a plane, which meet together, but are not in the same direction.
Side 5 - A straight line is that which lies evenly between its extreme points.
Side 15 - A cone is a solid figure described by the revolution of a right-angled triangle about one of the sides containing the right angle, which side remains fixed.